Результаты поиска

using a small screwdriver. Loosen socket head capscrew, but do not remove, Tap the head of the capscrew down to break the seal created by the tapered...

clothing wire lar material to the plates. drill.a tap arch casting for||capscrew after i:X Ix Figure 3. HEX. h;0. ASS'Y. GAPSCREW Top Plate mounting...

the rusted end of a capscrew that has been twisted off when trying to remove it from the part into which it was screwed. Capscrews and tap bolts have a...

cutting list.) (7) Hardware: Hexagonal capscrews (3/8 inch): capscrews 2 inches long. - 2 20 capscrews 4 inches long, 30 - Flathead bolts (10-32...

rivets, boxes. Setscrews, lb. 70 Copper rivets, lb. 776 Tin rivets, lb. Capscrews, lb. Boat spikes, lb. 2,550 Upholstering tacks, lb. Nalls, lb. 8,585 Steel...

Ring-Bowl Wear Ring - Impeller Suction Bearing - Suction Sandcollar Pipe Plug Capscrew-Hex DO NOT USE FOR CONSTRUCTION UNLESS CERTIFIED Certified By Project...

B leg C, is the enabling the D is fastened to B from below by capscrews. The table E is machined as shown in the detail and has a large hole through...

installed on the shaft with no hub fairwater cap, leaving the mounting capscrew and lockwasher exposed. Attached to the shaft housing 20 in upstream...

to the commencement of the study, operator was learning the system, capscrew the supporting the Figure 5.2) began to of tear the metal Pivot...

inserted, and a knot tied in the cord to prevent its slipping through the capscrew when the bob is suspended. Fig. 6 (b) is a special form CHAIN SURy EYING...

re-checked on the capscrews holding the locking wedges in place after 2 hours of operation. Check the torque on these wedge capscrews daily. Large slivers...

anchor J~OIA. STUD */A HEX NO'S FOUNDATION CASTiNCU------- - A0* CAPSCREW------^ 2~ ion UPPER P/HTl E CAST/NG TO GATE OIL 3 specificat A.S...

in.X7i in. T-head bolt and nut. 1.878 48 I in.Xli in. main-valve head capscrew. 11.389 49 Upper steam-cylinder gasket. 11,390 50 Lower steam-cylinder...

easily overstressed at assembly and are not used in primary structures. capscrews, spring lockwashers may be used when specified g. Close Tolerance Bolts...

into place on crib- bdng. to figure 2-4 and install the connection capscrews, lockwashers, and tocknuts so that the boom base section, insert (2) Refer...

gas, §10, p45. Cam, Worm, §15, p32. Cams, Bevel gears and, §15, p32. Capscrews, §15, p38. Causes and cure of hot bearings, §16, p46. of hot bearings...

SYSTEM PLATE A2 - 10,000 LB ~VERTICAL LOAD CELL +----- ------>'+ " CAPSCREWS AROUND PIPE, TO HOLD PLATES ROO END BORE -f BEARIN~S. -J- Y IN THREAD...

labor... 372 Capital and labor . 372 Capital mine steel ladders.*944 Capscrews, Replacing broken.*238 Car costs, Ariz. Cop. Co.*495 Car dump for tailings...

drilling holes of exact size is important. Tapped holes for threaded capscrews have proved satisfactory. If threads become stripped, nuts may be placed...

nerna.rKS. 4 5/8x4^ Bolts A. ij.il . 1.1 • UUU HttI t nrl at* 8 3/4xl^»» Capscrews U.S. qtri. 8 3/4k2m tt q q+d. U . O . O liU • ritiu. (Jiaty 32 5/8xl-£ »...